Replace Lock in UPVC Door
If you have a upvc door lock that isn't working correctly, you need to call an expert locksmith. They are fast efficient and can complete the job to the highest standards.
The process of changing a barrel lock made of upvc isn't a difficult task. It's not hard to change a upvc barrel lock.
Lock the barrel off.
uPVC windows and doors are typical in all kinds of properties. They allow natural light to be able to enter the home and can be opened with ease using the correct key. Switching the barrel of a lock on the uPVC door is a simple task that takes only five minutes. If you have lost your keys, or a tenant has left but has not returned them, or if the barrel of the lock has been damaged it is a simple solution.
The first thing you have to do is remove the screws that hold the handles. The handles will be moved out of the way so that you can access the barrel screws for the lock. It is important not to loosen the screws fast because this could damage the handles.
After the screws have been removed, look for the screw that holds the barrel lock in position on the inside of your door. This screw is distinct in color to the other screws on your door and sticks out. Remove the screw using a Phillips screwdriver. You can take the key you use to open the lock, and place it inside the barrel. Turn it to the right as much as you can. This will release the barrel and make it easier to take off the door.
After loosening the screw, you are now able to break the pins that hold the Euro Cylinder. To do this, you will need strong pliers or mole grips. Take the protruding portion of the euro cylinder, and bend it from side to side, and then up and down. This will break the two pins holding it in place.
Installing the new cylinder can be completed after the previous one is removed. First, you will need to measure the size of the lock cylinder in order to ensure that you have bought the correct replacement. You can do this by measuring the distance between the middle of the circular keyhole and the center square spindle. The measurement must be taken from the upper hole of the spindle.
Changing the Cylinder
The primary locking mechanism is the euro cylinder. It is easy to change and don't need a locksmith or handyman service. If your lock doesn't have this protection, you should replace it with one that has. They are incredibly inexpensive and could save you money as well as inconvenience when your locks are compromised by these security threats.
Open the door and stand in the front. This allows you to reach the handle retaining screws by hand or with an appropriate tool. You can loosen this screw a little bit or perhaps a quarter turn to get started.
The cylinder will be able to be removed easily since the screw will not be able to hold it in position. Next, you will need to decide what size replacement cylinder you require. There are around 25 different sizes. You should bring your previous cylindrical when you buy a new one to make sure it fits.
If you're not sure of the measurement, take a measurement from the screw hole center to the cylinder's end. You can only ensure that you're buying the right sized cylinders for your door made of upvc by measuring from the center of the screw hole to the end of the cylinder.
Install the new cylinder on your door in the opposite direction you removed the old one. The alignment of the lock cam can be a challenge, but it is typically a matter of alignment.
The next step is to insert the long screws for securing. After this is done, you can test the new cylinder and ensure that it is securely within the door. Then, you can reconnect the handle to the door and then test it again. If everything is functioning properly, your cylinder lock on your door made of upvc has been replaced and you have added a layer of security for your home.
Change the handle
There are many reasons why a door knob or handle can become loose. It could be due to the wear and tear on the handle or the square spindle inside the handle. In this case the door handle will need to be replaced.
It is important that the door is propped open so it cannot close between taking off the handle and replacing it. Then, remove the screws from the interior face of the handle plate by using a screwdriver. This will free the handle from the plate. Be careful not to lose the screws as they'll have to be re-screwed to their original position later.
It is now possible to remove the handles to gain access to the cylinder lock within the door. The cylinder lock will be round or bulb-shaped and is only used in multi-point locks on upvc and some aluminum doors. The procedure of changing the cylinder is similar to that of changing the handle, but you'll need to take the old cylinder from the door and replace it with a brand new one.
When choosing a replacement handle it is important to think about the size. Make sure the handle is of a similar size to the original one as it will have to be able to fit over the screws that hold the handle in place. A good place to start is to refer to the size matrix that will list the common sizes of replacement handles, as well as their keyhole center to handle plate distance.
Consider upgrading your door handles made of upvc to a higher security standard, such as a Sold Secure SS301 set or 2* Kitemark security handles. This will increase the security of your home, as well as making it easier to operate the door. These sets are slightly more expensive however the added security and peace of mind is worth it. You don't want to have to push the door handle constantly upwards and downwards to open or close it.
Changing the Lock
The lock on your uPVC door could be a vulnerable point for thieves. You may want to upgrade your uPVC door with a multipoint lock to increase the security. This would include an open hook as well as deadbolts to deter burglars. You can get a professional locksmith to help you, but you can also do it yourself. You'll require several tools, but the procedure is simple and fast.
The first step is to loosen the screws that hold the handle in the position. You can take the screws off using a screwdriver and put them in a secure place. Then, you can lift the handle and expose the screw holding the cylinder in position. The screw can be removed and replaced with a brand new one. You should make sure that the screw is exactly the same size as the original. double glazed window lock repair Repair My Windows And Doors should line up correctly to the barrel of the lock.
Making changes to the lock on your uPVC door could appear daunting. You depend on it to secure your home, and mistakes could cause you to be without a way to unlock the door. If you are able to figure it out, it's relatively easy and costs less than calling a professional locksmith.
You'll need to remove the faceplate on the inside of the lock in order to change the lock. You will need to see the screws inside the door and the retaining bolt outside the door. Once you are able to access these screws, you are able to remove the faceplate and replace it with a cylinder.
You might need to alter the lock on your uPVC door for several reasons. It could be a lost key, or a tenant moved out and didn't return the keys, or you simply want to increase the security of your home.
Anyone with basic DIY skills can alter the locking mechanism made of uPVC. You'll need to examine the hinges inside the mechanism, which could be difficult to do in the event that the lock is stuck. If the hinges have been lubricated it is a simple repair. However, if you're not confident doing this, it is best to call an expert.